| Author |
Message |
Harvey
Joined: 02 Mar 2008
Posts: 66
Location: Germany Lennestadt NRW
|
| Posted: Sun Mar 02, 2008 12:02 pm Post subject: Metropolis Image 1- HV Dead the same i think as CPD750 Runco |
|
|
The Labels intern shows all Mexico ... (I am from Germany pleas look not so exactly at my Language  ) )
My Problem is that the horizontal Transistor is blown dead to short cyrcit.
The Number on it is TZ1239 is this a NPN or PNP Type and what´s about the Voltage and the Current ?
Can i use a other one this is very expensive here over 35$.
Is there any reason that this Part blow´s away ... must i change other part´s to.
The Projector starts over FB but the right Power suply on the Back makes a noise that is not yery nice.
Is this a reason of the not connectet HV Trans. or is there a other reason for the nois.
Wath´s about the Focus and screen splitter Board... must i change it.. or can i test the unit after change of the Trans.
with this wires not looked at the tubes.
Pleas answer me for further details... Thank´s from Germany near Cologne. J.Haverland
www.harvey-electronics.de
|
|
| Back to top |
|
 |
kschmit2
Joined: 09 Mar 2006
Posts: 1141
Location: Heidelberg, Germany
|
| Posted: Sun Mar 02, 2008 1:04 pm Post subject: |
|
|
It's a rebadged Zenith 840/850 unit.
See here for more info: http://www.curtpalme.com/Zenith841.shtm
Zenith PJs were manufactured in Mexico iirc.
Btw, if you think $35 to get a PJ going again (be it CRT or any digital) is too much I don't think you are into the right hobby  Though I must admit that I wouldn't want to invest much more than that into a baseband unit.
Kai
EDIT: it was not RCF, but Zenith
| Description: |
|
| Filesize: |
5.96 KB |
| Viewed: |
7091 Time(s) |
|
| Description: |
| Metropolis Image One Specifications |
|
Download |
| Filename: |
Metropolis Image One.pdf |
| Filesize: |
124.56 KB |
| Downloaded: |
707 Time(s) |
|
|
| Back to top |
|
|
Curt Palme
CRT Tech
Joined: 08 Mar 2006
Posts: 24396
Location: Langley, BC
TV/Projector: All of them!
|
| Posted: Sun Mar 02, 2008 3:15 pm Post subject: |
|
|
It's a PRO 841 or 851. I have those transistors c/w mounting plate, $25.00 shipped to you. ANy standard H output transistor will work though, 8 amp, 1500 volts.
Chances are your HV board might be bad as well though, Zenith had a bad run of those way back when, I'm still seeing sets with low hours that haven't blown until recently. I've got those 9-848 boards as well.
|
|
| Back to top |
|
|
Harvey
Joined: 02 Mar 2008
Posts: 66
Location: Germany Lennestadt NRW
|
| Posted: Sun Mar 02, 2008 6:28 pm Post subject: The Board I think is bad |
|
|
 Now i have used a 2SC5421 it works but the Power drops from 150 to 92V and the Tr. goes hot..
The Osziloskope shows a Signal but i think the Flyback Trafo is short ...
I Have losen all Kabels from the HV Trafo to the Focus and Screen Board ... but there is no high Voltage on it
A littel but i think much to low...
The Number on the Trafo is 95-4170-02 My list of HR-Dimen goes over this number but the number is not in my List.
Can you tell me the Price of this unit (Trafo or kopmplete Board) and is it necessarie to change the Focus and sreen Board to.??
With the 35$ i men only that i have a lott of things laying here and i thougt i hade such thing...  I Thing i had it...
I know that you can´t fix such unit with 35$....
I thank you for your fast reply and see forward for another... J.Haverland 
|
|
| Back to top |
|
|
Harvey
Joined: 02 Mar 2008
Posts: 66
Location: Germany Lennestadt NRW
|
| Posted: Sun Mar 02, 2008 6:29 pm Post subject: another Question |
|
|
Is this unit Pal or NTSC or both how can i see this ...
Is there any Board on wich i can see if it is Pal ????
|
|
| Back to top |
|
|
Curt Palme
CRT Tech
Joined: 08 Mar 2006
Posts: 24396
Location: Langley, BC
TV/Projector: All of them!
|
| Posted: Sun Mar 02, 2008 6:33 pm Post subject: |
|
|
I believe the ones sent to Europe were all 220 volt and PAL. I've got a couple of 220 V power supplies that I'd throw in at no charge (except for shipping). Video processing is done on the 9-700 board. There were different chips depending on where the set was sent.
The 9-848 board is $150 plus shipping. I'd ship the board, I'd risk breaking the transformer wires if I unsoldered the transformer from the PC board. Shipping would be about $40, $55 with the power supply board that I'd throw in for free.
|
|
| Back to top |
|
|
Harvey
Joined: 02 Mar 2008
Posts: 66
Location: Germany Lennestadt NRW
|
| Posted: Sun Mar 02, 2008 6:40 pm Post subject: |
|
|
How much is then the total amount for shipping and the Part´s...
Have you a layout cyrcit Page of the Projektor Model ... for some Reason it help´s ...
And whatá about the Focus and screen Board it is a Set of 2 Things the grey Block and a Black peace with 6 Potis in it..
can you tell me a Price of it to.
|
|
| Back to top |
|
|
macgyver655
Joined: 22 Aug 2007
Posts: 8508
|
| Posted: Sun Mar 02, 2008 6:43 pm Post subject: |
|
|
|
Another thing to remember when replaceing a blown Horz output transistor is to check for poor solder joints in that circuit, especially the Horz drive transformer. Also when it blows it can take out some of the caps in that circuit as well. Good Luck.
|
|
| Back to top |
|
|
Harvey
Joined: 02 Mar 2008
Posts: 66
Location: Germany Lennestadt NRW
|
| Posted: Sun Mar 02, 2008 7:28 pm Post subject: Payment of the Part´s i need |
|
|
Can i Pay with Pay-Pal or wich way do you prefer...
mail me to info@harvey-electronics.de please
|
|
| Back to top |
|
|
kschmit2
Joined: 09 Mar 2006
Posts: 1141
Location: Heidelberg, Germany
|
| Posted: Sun Mar 02, 2008 8:02 pm Post subject: |
|
|
| Curt Palme wrote: | I believe the ones sent to Europe were all 220 volt and PAL. I've got a couple of 220 V power supplies that I'd throw in at no charge (except for shipping). Video processing is done on the 9-700 board. There were different chips depending on where the set was sent.
The 9-848 board is $150 plus shipping. I'd ship the board, I'd risk breaking the transformer wires if I unsoldered the transformer from the PC board. Shipping would be about $40, $55 with the power supply board that I'd throw in for free. |
Curt,
the "specs" I posted indicate that there was a "Metropolis Image One Multi" that was PAL and NTSC capable.
I would assume that there would be some kind of label on it though.
Kai
|
|
| Back to top |
|
|
Harvey
Joined: 02 Mar 2008
Posts: 66
Location: Germany Lennestadt NRW
|
| Posted: Sun Mar 02, 2008 8:08 pm Post subject: |
|
|
 What Label is in to see if it is Multi or Pal or )))
So another Question about the HS Transistor Board... (2SC5421)
There is a Resistor mounted on it (under it) from the Basis to the Emitter labeld red red Black...
Is that real or is this a modyfied ... need it or better pull it away... ????
|
|
| Back to top |
|
|
Malakay
Joined: 16 Mar 2006
Posts: 49
Location: Germany
|
| Posted: Tue Mar 04, 2008 2:23 pm Post subject: |
|
|
My first beamer also was a Image1, i bought it in Mannheim
My Model was a Pal/NTSC Model. A Big sticker with "PAL/NTSC" was an on the back on the crt.
But u can also test it, the are a few buttons on the crt, i think it was the one button next to the power button. Press it once and the crt goes of. Switch em back on again and when u get an black/white picture, it is a multinorm beamer
regards
Chris
|
|
| Back to top |
|
|
Harvey
Joined: 02 Mar 2008
Posts: 66
Location: Germany Lennestadt NRW
|
| Posted: Tue Mar 04, 2008 2:42 pm Post subject: |
|
|
I will test this wenn my Beamer is fixed... I have no Picture at the Time the HV Board is dead.
_________________
.....Was nicht geht läuft irgendwann...
.......lieber 5 mal löten als einmal.......
|
|
| Back to top |
|
|
|
|
