|
As this forum is rarely used anymore, we've locked it. Feel free to browse and read. Questions? Please reach out to us directly. Cheers! |
|
 |
|
|
| Author |
Message |
Danke
Joined: 13 Jan 2007
Posts: 123
|
| Posted: Sat Jan 28, 2012 6:09 pm Post subject: No Picture with Marquee VIM-FULLHD v3 HDMI 1.3 Input Card |
|
|
I just installed the card into my 8111.
Selected source 02. (tried other source numbers too).
Tried both HDMI inputs.
Went from both my Yamaha receiver and direct from the PS3 to the card.
Lights on the card:
Link and Det lights on.
Status
1 2
3 4
5 6
Status lights 3,4 and 6 on with PS3. Just 4 and 6 with PS3 thru the Receiver. Lights 2 and 6 with DTV.
Any ideas what I'm doing wrong?
Thanks!
|
|
| Back to top |
|
 |
draganm
Joined: 08 Mar 2006
Posts: 8990
Location: Colorado
|
| Posted: Sat Jan 28, 2012 7:02 pm Post subject: Re: No Picture with Marquee VIM-FULLHD v3 HDMI 1.3 Input Car |
|
|
| Danke wrote: | I just installed the card into my 8111.
Selected source 02. (tried other source numbers too).
|
there is no "source" on a marquee. There's inputs and channels. are you sure it's input 02 and not just channel 02? if your on channel 2 it could be any input assigned to it.
Go into Utility's, source set-up, channel list. Choose a channel like channel 5 for instance, scroll over and assign input 02, recall 05 . Now exit and push 5 + Enter
|
|
| Back to top |
|
|
Danke
Joined: 13 Jan 2007
Posts: 123
|
| Posted: Sun Jan 29, 2012 11:03 pm Post subject: |
|
|
Well the manual and remote have "source." Anyway, I was doing it correctly, but for some reason for when selecting source/input 02, the contrast and brightness were turned all the way down. So no picture, doh! Have a prety good picture, just a little dark. But I'll have to wait until I'm back in town to look into that.
The manual for Moome's card says: "We can see the panel, there is two little pot, one for contrast adjustment (need
professional person to do this), another one use for gamma level adjustment.
Below is adjustment way"
"【Note】Please don't turn the contrast pot if you have no instrument to measure
white level. (The factory default is 0.7V for white"
So should I leave those alone or is that just for contrast pot?
"
Last edited by Danke on Sun Jan 29, 2012 11:11 pm; edited 1 time in total
|
|
| Back to top |
|
|
dturco
Joined: 06 Feb 2009
Posts: 3778
Location: Eastern Shore Maryland
TV/Projector: Runco DLP VX-3000i Marquee 9500 parts doner
|
| Posted: Sun Jan 29, 2012 11:10 pm Post subject: |
|
|
| Danke wrote: | Well the manual and remote have "source." Anyway, I was doing it correctly, but for some reason for when selecting source/input 02, the contrast and brightness were turned all the way down. So no picture, doh! Have a prety good picture, just a little dark. But I'll have to wait until I'm back in town to look into that.
The manual for Moome's card says: "We can see the panel, there is two little pot, one for contrast adjustment (need
professional person to do this), another one use for gamma level adjustment.
Below is adjustment way"
So should I leave those alone? |
Yes leave them alone. The were set at the factory. They shouldn't even be there really. If you adjust them you will change the Peak to Peak voltage {.07} needed to display full white and black, correctly. This would throw off your colors.
Do not adjust them 
_________________
Firefly rules. Can't stop the signal.
http://www.hulu.com/firefly
|
|
| Back to top |
|
|
Danke
Joined: 13 Jan 2007
Posts: 123
|
| Posted: Sun Jan 29, 2012 11:15 pm Post subject: |
|
|
| dturco wrote: | | Danke wrote: | Well the manual and remote have "source." Anyway, I was doing it correctly, but for some reason for when selecting source/input 02, the contrast and brightness were turned all the way down. So no picture, doh! Have a prety good picture, just a little dark. But I'll have to wait until I'm back in town to look into that.
The manual for Moome's card says: "We can see the panel, there is two little pot, one for contrast adjustment (need
professional person to do this), another one use for gamma level adjustment.
Below is adjustment way"
So should I leave those alone? |
Yes leave them alone. The were set at the factory. They shouldn't even be there really. If you adjust them you will change the Peak to Peak voltage {.07} needed to display full white and black, correctly. This would throw off your colors.
Do not adjust them |
Wow, thanks for the quick response. I was just editing my post and now I see you had already responded!
|
|
| Back to top |
|
|
draganm
Joined: 08 Mar 2006
Posts: 8990
Location: Colorado
|
| Posted: Mon Jan 30, 2012 3:35 am Post subject: |
|
|
|
one thing I would do is set the output range to 0/255 instead of 16/235. I could not get a good CRT-like picture with the second choice which is the default
|
|
| Back to top |
|
|
|
|
|
|
|
You cannot post new topics in this forum
You cannot reply to topics in this forum
You cannot edit your posts in this forum
You cannot delete your posts in this forum
You cannot vote in polls in this forum
You cannot attach files in this forum
You can download files in this forum
|
Forum powered by phpBB © phpBB Group
|
|
