| Author |
Message |
tmacklin
Joined: 10 Jul 2007
Posts: 5
Location: Birmingham, AL
TV/Projector: NEC 10PG
|
| Posted: Sat Jun 13, 2009 9:10 pm Post subject: New EXT-FULLHD config issues |
|
|
I have a NEC 10PG running RGBHV-VGA cable back to a Moome EXT-FULLHD through to a Dish Network DVR. I have tried copying input settings from one memory location to another, creating a new input, etc, and this "double image" split down the middle of the screen is the best I can get (picture attached). The one oddity I can see is the fact that the Moome box light over the "SEL" button is flickering red-green incessantly. I'm assuming this is not what it is supposed to be doing, but I can't find anything in the documentation that says what it means.
Thanks in advance for any configuration ideas!
-Tim Macklin
Birmingham, AL
| Description: |
|
| Filesize: |
21.92 KB |
| Viewed: |
6357 Time(s) |
|
_________________
No bucks... no Buck Rogers!
-Gus Grissom "The Right Stuff"
|
|
| Back to top |
|
 |
tmacklin
Joined: 10 Jul 2007
Posts: 5
Location: Birmingham, AL
TV/Projector: NEC 10PG
|
| Posted: Sun Jun 14, 2009 4:27 pm Post subject: Output problem solved... |
|
|
I now have a single image after resetting jumper #5 and re"SEL"ing the unit. Now I have a problem with the PJ holding a convergence. If I power off the projector and restart it, I get the "INCOMPATIBLE MATCH!! CHECK INPUT LIST." error message and I have to reconverge. I'm assuming that this is related to the input setup, but I'm not sure how to address it.
Any help out there?
Thanks!
_________________
No bucks... no Buck Rogers!
-Gus Grissom "The Right Stuff"
|
|
| Back to top |
|
|
moome
Joined: 01 Jun 2007
Posts: 497
|
| Posted: Mon Jun 15, 2009 9:38 am Post subject: Re: Output problem solved... |
|
|
| tmacklin wrote: | I now have a single image after resetting jumper #5 and re"SEL"ing the unit. Now I have a problem with the PJ holding a convergence. If I power off the projector and restart it, I get the "INCOMPATIBLE MATCH!! CHECK INPUT LIST." error message and I have to reconverge. I'm assuming that this is related to the input setup, but I'm not sure how to address it.
Any help out there?
Thanks! |
when yo get the box? you can send it back for software upgrade~
|
|
| Back to top |
|
|
moome
Joined: 01 Jun 2007
Posts: 497
|
| Posted: Mon Jun 15, 2009 9:45 am Post subject: Re: New EXT-FULLHD config issues |
|
|
| tmacklin wrote: | I have a NEC 10PG running RGBHV-VGA cable back to a Moome EXT-FULLHD through to a Dish Network DVR. I have tried copying input settings from one memory location to another, creating a new input, etc, and this "double image" split down the middle of the screen is the best I can get (picture attached). The one oddity I can see is the fact that the Moome box light over the "SEL" button is flickering red-green incessantly. I'm assuming this is not what it is supposed to be doing, but I can't find anything in the documentation that says what it means.
Thanks in advance for any configuration ideas!
-Tim Macklin
Birmingham, AL
|
hi:
you can send the defective unit to me and i will repair it for you.
my email is:moome@curtpalme.com
thanks
Moome
|
|
| Back to top |
|
|
moome
Joined: 01 Jun 2007
Posts: 497
|
| Posted: Mon Jun 15, 2009 10:05 am Post subject: Re: Output problem solved... |
|
|
| tmacklin wrote: | I now have a single image after resetting jumper #5 and re"SEL"ing the unit. Now I have a problem with the PJ holding a convergence. If I power off the projector and restart it, I get the "INCOMPATIBLE MATCH!! CHECK INPUT LIST." error message and I have to reconverge. I'm assuming that this is related to the input setup, but I'm not sure how to address it.
Any help out there?
Thanks! |
did you press the Store botton on the remote to save adjusted alignment value in a new input entry?
|
|
| Back to top |
|
|
tmacklin
Joined: 10 Jul 2007
Posts: 5
Location: Birmingham, AL
TV/Projector: NEC 10PG
|
| Posted: Mon Jun 22, 2009 4:42 pm Post subject: Making SLOOOOW progress... |
|
|
Now I have figured out the input storage problem... I have the PJ keeping a full convergence, but now I am getting "ghosts" of red and blue around areas of high contrast in the picture. I have checked the convergence thoroughly, and the blue and red ghosts only appear in areas of the picture that have high contrast (dark and light elements juxtaposed with one another) and then disappear when the picture have no aras of high contrast. Is this related to the EXT-FULLHD's trimpot settings for gamma, etc?
Thanks in advance!
-Tim Macklin
Birmingham, AL
_________________
No bucks... no Buck Rogers!
-Gus Grissom "The Right Stuff"
|
|
| Back to top |
|
|
|
|
