| Author |
Message |
charlez
Joined: 16 Nov 2006
Posts: 78
Location: Belgium
|
| Posted: Wed May 27, 2009 4:27 pm Post subject: How to install contrast modulation board ? |
|
|
hi,
Just bought a contrast modulation board for my bd808S but no idea where to connect the wires.
One goes to the vertical deflection board, but what to do with the other one?
Does someone have a schema for this ?
And after that what is the correct procedure for using the board ?
thx
|
|
| Back to top |
|
 |
WTS
Joined: 08 Mar 2006
Posts: 1276
Location: Calgary
|
| Posted: Wed May 27, 2009 6:07 pm Post subject: |
|
|
the cm goes on the rgb driver board.
_________________
Thanks
Walter
|
|
| Back to top |
|
|
charlez
Joined: 16 Nov 2006
Posts: 78
Location: Belgium
|
| Posted: Wed May 27, 2009 6:11 pm Post subject: |
|
|
|
there are no spare connectors on that fit.
|
|
| Back to top |
|
|
Decibel
Joined: 31 May 2007
Posts: 904
Location: Roma - Italia
|
| Posted: Wed May 27, 2009 11:57 pm Post subject: Re: How to install contrast modulation board ? |
|
|
| charlez wrote: |
Does someone have a schema for this ? |
Part number?
This is my contrast modulation board
_________________
Domenico (Barco fan!)
|
|
| Back to top |
|
|
WTS
Joined: 08 Mar 2006
Posts: 1276
Location: Calgary
|
| Posted: Thu May 28, 2009 1:01 pm Post subject: |
|
|
There is only one connector required and the CM board has the connector/wire attached to it just plug it into the RGB driver like the picture shows.
_________________
Thanks
Walter
|
|
| Back to top |
|
|
charlez
Joined: 16 Nov 2006
Posts: 78
Location: Belgium
|
| Posted: Thu May 28, 2009 3:07 pm Post subject: |
|
|
i've got an other version of board.
Mine come's in place of port 3.
nr. R761876
|
|
| Back to top |
|
|
WTS
Joined: 08 Mar 2006
Posts: 1276
Location: Calgary
|
| Posted: Thu May 28, 2009 6:09 pm Post subject: |
|
|
I'm not familiar with that one.
_________________
Thanks
Walter
|
|
| Back to top |
|
|
TbX
Joined: 06 May 2006
Posts: 94
Location: Sweden
|
| Posted: Thu May 28, 2009 6:26 pm Post subject: |
|
|
|
it does not fit in a 808s only 800,801,808 non s
|
|
| Back to top |
|
|
charlez
Joined: 16 Nov 2006
Posts: 78
Location: Belgium
|
| Posted: Thu May 28, 2009 6:33 pm Post subject: |
|
|
| TbX wrote: | | it does not fit in a 808s only 800,801,808 non s |
Are you shure ?
I bought it from curt and asked for a contrast modulation board for a BD808S.
|
|
| Back to top |
|
|
Decibel
Joined: 31 May 2007
Posts: 904
Location: Roma - Italia
|
| Posted: Fri May 29, 2009 8:26 am Post subject: |
|
|
@ Charlez
PM your email address, please.
I will send pdf document of the 808 (non s) contrast modulation board.
_________________
Domenico (Barco fan!)
Last edited by Decibel on Fri May 29, 2009 10:29 am; edited 1 time in total
|
|
| Back to top |
|
|
Decibel
Joined: 31 May 2007
Posts: 904
Location: Roma - Italia
|
| Posted: Fri May 29, 2009 10:17 am Post subject: |
|
|
| charlez wrote: | i've got an other version of board.
Mine come's in place of port 3.
nr. R761876 |
In R761876 service manual there's two connectors
1) To RGB Driver
2) From RGB Input & Input switching
There's other connectors but in case of presence Soft Edge Modulation & IBC Link boards or/and orbiting board.
_________________
Domenico (Barco fan!)
|
|
| Back to top |
|
|
Decibel
Joined: 31 May 2007
Posts: 904
Location: Roma - Italia
|
| Posted: Fri May 29, 2009 10:28 am Post subject: |
|
|
| TbX wrote: | | it does not fit in a 808s only 800,801,808 non s |
I think that this is correct 
_________________
Domenico (Barco fan!)
|
|
| Back to top |
|
|
RVonse
Joined: 09 Mar 2006
Posts: 3152
|
| Posted: Sat May 30, 2009 10:07 pm Post subject: |
|
|
|
What good is a contrast modulation card going to do for you? Are you expecting to blend by using this card?
|
|
| Back to top |
|
|
|
|
