| Author |
Message |
Superbit1978
Joined: 27 Oct 2008
Posts: 19
|
| Posted: Thu Oct 30, 2008 2:42 pm Post subject: Chance to front table |
|
|
Hello people i would like to now.Where do i change the Scan adaption for my barco 800 graphics i have the manuel but it is strange you see 3 pins and thats it  you don.t see where it is  anyway thanks
patrick
|
|
| Back to top |
|
 |
Person99
Joined: 09 Mar 2006
Posts: 4899
Location: Flower Mound, TX
|
| Posted: Thu Oct 30, 2008 4:16 pm Post subject: |
|
|
The scan inversion switches are on the system's main board in the card cage area. They are under the cards (they are white rectangles about an inch and a half long or so). You should be able to see them looking between the cards. You need to pull out a couple cards to access them. Their location and proper settings for front table are on page 27 of the installation manual which is available on this site.
_________________
Dave
A train station is where the train stops. A bus station is where the bus stops. On my desk, I have a work station....
|
|
| Back to top |
|
|
Superbit1978
Joined: 27 Oct 2008
Posts: 19
|
| Posted: Thu Oct 30, 2008 4:59 pm Post subject: |
|
|
thanks dave i will take a look at it. so i can take the cards out with no problem right
regards patrick
|
|
| Back to top |
|
|
Superbit1978
Joined: 27 Oct 2008
Posts: 19
|
| Posted: Thu Oct 30, 2008 5:23 pm Post subject: |
|
|
Hello people look i see 3 little pins on the bodem but they look all the same too me.so what do i need to change then................ because if i look at the manual i see 3 pins for one setup front table and for rear ceiling you see the same pins but in a larger spot beats me man
thanks regards patrick
|
|
| Back to top |
|
|
Superbit1978
Joined: 27 Oct 2008
Posts: 19
|
| Posted: Thu Oct 30, 2008 5:40 pm Post subject: |
|
|
Never mind i found it you need to push the little butons keep in touch later
regards patrick
|
|
| Back to top |
|
|
jkruger
Joined: 24 Oct 2007
Posts: 2435
Location: Carlsbad, CA
|
| Posted: Thu Oct 30, 2008 5:51 pm Post subject: |
|
|
|
Make sure the power is off when you change it.
|
|
| Back to top |
|
|
Person99
Joined: 09 Mar 2006
Posts: 4899
Location: Flower Mound, TX
|
| Posted: Thu Oct 30, 2008 7:01 pm Post subject: |
|
|
| jkruger wrote: | | Make sure the power is off when you change it. |
As in mains off and power cord uplugged!
_________________
Dave
A train station is where the train stops. A bus station is where the bus stops. On my desk, I have a work station....
|
|
| Back to top |
|
|
Superbit1978
Joined: 27 Oct 2008
Posts: 19
|
| Posted: Thu Oct 30, 2008 7:53 pm Post subject: |
|
|
Yeah i read that in the manual love this CRT thing.oke one problem i pushed the butenes and the image was good but when i was adjusting the raster GREEN FIRST AND RED with no problem and then the BLUE raster image letters was like looking true a mirror....you guys now wath this is
regards patrick
|
|
| Back to top |
|
|
jkruger
Joined: 24 Oct 2007
Posts: 2435
Location: Carlsbad, CA
|
| Posted: Thu Oct 30, 2008 8:00 pm Post subject: |
|
|
|
You mean the letters are reversed? if so, then you need to change one of the switches. Shut the power OFF first!
|
|
| Back to top |
|
|
Superbit1978
Joined: 27 Oct 2008
Posts: 19
|
| Posted: Thu Oct 30, 2008 8:07 pm Post subject: |
|
|
Correct SIR the blue letters are reversed. will take a look at the switches again later on. thanks Kruger
regards patrick
|
|
| Back to top |
|
|
Person99
Joined: 09 Mar 2006
Posts: 4899
Location: Flower Mound, TX
|
| Posted: Fri Oct 31, 2008 2:06 pm Post subject: |
|
|
Those switches are not exactly the best part Barco ever used. Make extra sure they are all in the correct position.
I assume you are front table to play with it before mounting, or are you going to upgrade before mounting?
_________________
Dave
A train station is where the train stops. A bus station is where the bus stops. On my desk, I have a work station....
|
|
| Back to top |
|
|
|
|
