Return to the CurtPalme.com main site CurtPalme.com Home Theater Forum
A forum with a sense of fun and community for Home Theater enthusiasts!
Products for Sale ] [ FAQ: Hooking it all up ] [ CRT Primer/FAQ ] [ Best/Worst CRT Projectors List ] [ Setup Tips & Manuals ] [ Advanced Procedures ] [ Newsletters ]

 
Forum FAQForum FAQ   SearchSearch   MemberlistMemberlist  Photo AlbumsPhoto Albums  RegisterRegister 
 MembershipClub Membership   ProfileProfile   Private MessagesPrivate Messages   Log inLog in 
Blu-ray disc release list and must-have titles. Buy the latest and best Blu-ray titles to show off in your home theater!

Tube pinout question
Goto page Previous  1, 2, 3, 4, 5
 
Post new topic   Reply to topic   Printer-friendly view    CurtPalme.com Forum Index -> CRT Projectors
View previous topic :: View next topic  
Author Message
El Duderino




Joined: 23 Jan 2011
Posts: 4627
Location: Portland, OR


PostLink    Posted: Sat Jan 05, 2019 1:36 am    Post subject: Reply with quote


        Register to remove this ad. It's free!
km987654 wrote:
No I have not but I suspect the full brightness is caused by NO G1.

Here are two neck cards of two 9" Sony tubes. If you look very closely at the SD146a neck card you can see it is labeled and has pin 9 connected to g1 (pin 4 is lower right and pin 5 is labeled g2). If you look at BG808s neck card you can see pin 9 is not connected. Sorry I cannot put label on picture at the moment.


Perhaps it's just camera / lighting artifacts, but several of the solder fillets on the SD146 image appear to be cold/cracked and worthy of a reflow to me. Laughing
Back to top
km987654




Joined: 25 Jul 2007
Posts: 2852
Location: Australia

TV/Projector: Barco BG809s


PostLink    Posted: Sat Jan 05, 2019 3:35 am    Post subject: Reply with quote

El Duderino wrote:
km987654 wrote:
No I have not but I suspect the full brightness is caused by NO G1.

Here are two neck cards of two 9" Sony tubes. If you look very closely at the SD146a neck card you can see it is labeled and has pin 9 connected to g1 (pin 4 is lower right and pin 5 is labeled g2). If you look at BG808s neck card you can see pin 9 is not connected. Sorry I cannot put label on picture at the moment.


Perhaps it's just camera / lighting artifacts, but several of the solder fillets on the SD146 image appear to be cold/cracked and worthy of a reflow to me. Laughing


Probably right. Those have not been used for years.
Back to top
ElTopo




Joined: 07 Nov 2006
Posts: 1607



PostLink    Posted: Wed Oct 11, 2023 9:41 am    Post subject: Re: another tube pinout question Reply with quote

[quote="Decibel"]Can I use panasonic 180dvb22 or P16LNP/LNQ neckboards simply by rotating them 180 degrees in P19LCP07's/LPB's and Lug's?

The socket is rotate but pinout is the same.[/quote]


Anyone out there did that in reality ?

P19LUG into a Barco 808s !

If i’m reading this correct the neckboards can be put 1:1 on the P19LUG ?

thanks

_________________
Barco Cine 9 the one and only
Back to top
Display posts from previous:   
Post new topic   Reply to topic   Printer-friendly view    CurtPalme.com Forum Index -> CRT Projectors All times are GMT
Goto page Previous  1, 2, 3, 4, 5
Page 5 of 5
Jump to:  
You cannot post new topics in this forum
You cannot reply to topics in this forum
You cannot edit your posts in this forum
You cannot delete your posts in this forum
You cannot vote in polls in this forum
You cannot attach files in this forum
You can download files in this forum