Return to the CurtPalme.com main site CurtPalme.com Home Theater Forum
A forum with a sense of fun and community for Home Theater enthusiasts!
Products for Sale ] [ FAQ: Hooking it all up ] [ CRT Primer/FAQ ] [ Best/Worst CRT Projectors List ] [ Setup Tips & Manuals ] [ Advanced Procedures ] [ Newsletters ]

 
Forum FAQForum FAQ   SearchSearch   MemberlistMemberlist  Photo AlbumsPhoto Albums  RegisterRegister 
 MembershipClub Membership   ProfileProfile   Private MessagesPrivate Messages   Log inLog in 
Blu-ray disc release list and must-have titles. Buy the latest and best Blu-ray titles to show off in your home theater!

NEC XG52 shutoff and error code

 
Post new topic   Reply to topic   Printer-friendly view    CurtPalme.com Forum Index -> CRT Projectors
View previous topic :: View next topic  
Author Message
paiaboy7




Joined: 15 Aug 2008
Posts: 65



PostLink    Posted: Mon Nov 26, 2018 8:59 pm    Post subject: NEC XG52 shutoff and error code Reply with quote


        Register to remove this ad. It's free!
I have a NEC XG52 CRT projector currently not working. As soon as you try to turn on the power, it starts to power up then just immediately shuts itself off. It will cycle a couple of times trying to turn on but nothing else happens. It was working fine then this issue came up all of a sudden. The picture shows the error code that comes up on the rear display of the projector. Any suggestions? Thanks!



error code.jpg
 Description:
 Filesize:  54.99 KB
 Viewed:  3732 Time(s)

error code.jpg


Back to top
Curt Palme
CRT Tech



Joined: 08 Mar 2006
Posts: 24296
Location: Langley, BC

TV/Projector: All of them!


PostLink    Posted: Tue Nov 27, 2018 4:52 am    Post subject: Reply with quote

Is that a CC error or FC?
Back to top
paiaboy7




Joined: 15 Aug 2008
Posts: 65



PostLink    Posted: Wed Nov 28, 2018 1:20 am    Post subject: Reply with quote

It seemed like a cc but the bottom segment of the first c wasn't lit up.
Back to top
Curt Palme
CRT Tech



Joined: 08 Mar 2006
Posts: 24296
Location: Langley, BC

TV/Projector: All of them!


PostLink    Posted: Wed Nov 28, 2018 11:26 pm    Post subject: Reply with quote

A really tough call then. It could be FC, which is a problem on the +15 volt line. That could be almost any board in the set, and is very hard to troubleshoot.

I have no more XG parts at this point other than remote controls, so it will be up to a scrap set that someone might have here to get you going again.

http://www.curtpalme.com/docs/NECXG_Error_Codes.pdf
Back to top
paiaboy7




Joined: 15 Aug 2008
Posts: 65



PostLink    Posted: Thu Nov 29, 2018 12:01 am    Post subject: Reply with quote

Thanks for checking. Is CC an easier fix?
Back to top
pcheadaches




Joined: 09 Dec 2013
Posts: 62



PostLink    Posted: Thu Nov 29, 2018 12:25 am    Post subject: Reply with quote

Try reseating the system board a few times.
Back to top
Curt Palme
CRT Tech



Joined: 08 Mar 2006
Posts: 24296
Location: Langley, BC

TV/Projector: All of them!


PostLink    Posted: Thu Nov 29, 2018 12:34 am    Post subject: Reply with quote

CC is a system board error. I've never had that before, but i guess it's possible. Again, I have no parts, and the most common failure on XGs has been the system board, so finding a working system board will be tough.

Might be the time to go digital perhaps?
Back to top
paiaboy7




Joined: 15 Aug 2008
Posts: 65



PostLink    Posted: Thu Nov 29, 2018 6:07 pm    Post subject: Reply with quote

pcheadaches wrote:
Try reseating the system board a few times.


Thank you I'll try that
Back to top
Display posts from previous:   
Post new topic   Reply to topic   Printer-friendly view    CurtPalme.com Forum Index -> CRT Projectors All times are GMT
Page 1 of 1
Jump to:  
You cannot post new topics in this forum
You cannot reply to topics in this forum
You cannot edit your posts in this forum
You cannot delete your posts in this forum
You cannot vote in polls in this forum
You cannot attach files in this forum
You can download files in this forum