View previous topic :: View next topic |
Author |
Message |
Curt Palme CRT Tech
Joined: 08 Mar 2006 Posts: 24301 Location: Langley, BC
TV/Projector: All of them!
|
Link Posted: Wed Mar 29, 2017 1:46 am Post subject: Marquee goes dead when Moome inserted |
|
|
I have a customer that has had a myriad of issues with a Marquee I sold him. No need to go into details, but the last issue now seems to be that the set is dead when the Moome card is put in.
Seems to me that there was a cure for that, although it was all tested when I sent the Marquee Ultra up, and it was working when he received it.
I know it's possible that the card shorted out, but wasn't there an issue with this at one point, or was that an old version of the Moome card when it first came out?
Thanks!
|
|
Back to top |
|
|
draganm
Joined: 08 Mar 2006 Posts: 8990 Location: Colorado
|
Link Posted: Thu Mar 30, 2017 5:50 pm Post subject: |
|
|
yes, but it was a really old DVI card. Had to do with a jumper that set the card to draw from either the 5 or 15 volt rails. Some Marquee's didn't like the draw on the 5 volt rail
I have the schematic somewhere if that's the card you have
|
|
Back to top |
|
|
CIR Engineering
Joined: 25 Aug 2008 Posts: 4264 Location: Chicago USA & Berlin Germany
|
Link Posted: Thu Mar 30, 2017 6:31 pm Post subject: |
|
|
I had one once that had a short on the Moome board that would cause the Marquee to shut down and throw LVPS error code. Founds the short and all was well after that.
craigr
_________________ *NEW JETI 1501-HiRes 2nm Spectroradiometer
JETI 1211 Spectroradiometer
Photo Research PR-650 Spectroradiometer
Klein K10-A Colorimeter
X-Rite i1Pro2 Spectroradiometer & Spyder Colorimeters *For JVC auto-calibration when Klein & Jeti are not applicable
Murideo Fresco SIX-G HDMI 2.x Multimedia Generator
Murideo Fresco SIX-A HDMI 2.x Analyzer
*NEW Light Illusion ColourSpace XPT Version β Color Calibration Software
Light Illusion LightSpace XPT Pro Version 10.x Color Calibration Software
*NEW OMARDRIS JVC Software Patch to use K10-A and Jeti with JVC OEM AutoCal Software!
Sencore CR7000 CRT Tube Analyzer / Rejuvenater
Authorized Dealer for Lumagen & just about everything worth buying
www.CIR-Engineering.com - craigr@cir-engineering.com
Phone: 865-405-6892
|
|
Back to top |
|
|
Curt Palme CRT Tech
Joined: 08 Mar 2006 Posts: 24301 Location: Langley, BC
TV/Projector: All of them!
|
Link Posted: Thu Mar 30, 2017 7:11 pm Post subject: |
|
|
draganm wrote: | yes, but it was a really old DVI card. Had to do with a jumper that set the card to draw from either the 5 or 15 volt rails. Some Marquee's didn't like the draw on the 5 volt rail
I have the schematic somewhere if that's the card you have |
THAT'S what I was thinking of, thanks! I'll send the guy a replacement card, I may have one here.
|
|
Back to top |
|
|
draganm
Joined: 08 Mar 2006 Posts: 8990 Location: Colorado
|
Link Posted: Thu Mar 30, 2017 9:06 pm Post subject: |
|
|
ok, found my notes. This was literally the first card he ever made, DVI and component video. The Jumper positions are J1 closer to edge of card on back/left side or J2 slightly closer to center.
Recommended spot is J2
|
|
Back to top |
|
|
|
|