View previous topic :: View next topic |
Author |
Message |
Pellen
Joined: 31 Oct 2013 Posts: 10 Location: Sweden
|
Link Posted: Sat Oct 11, 2014 5:04 pm Post subject: BD 708s OSD |
|
|
Hi
I've got some problems with my Barco Data 708s.
The last 5 times I've been using it, suddenly there is one or more out of these three OSDs:
"Projector address: 0",
"Warning Invalid key entry" or
"Brightness 49"
They are only visible for 3 secs and it's about 3-15 mins in between.
The picture is perfect, but the remote isn't working when the OSD comes up and until I turn it off.
Last night, after a few OSDs the green CRT turned off.
Powered it off really quickly so I had no chance to check the LEDs.
Any ideas?
Yes, I tried to remove the remote battery. The remote is not transmitting.
Green CRT is OK today.
|
|
Back to top |
|
|
CasetheCorvetteman
Joined: 09 Nov 2008 Posts: 6319 Location: Australia
|
Link Posted: Sat Oct 11, 2014 10:13 pm Post subject: |
|
|
Clean the connector for the internal remote. Probably not that, but my CineMAX does something simular when im trying to use the remote sometimes, i havent done anything to figure out why yet.
_________________ Barco CineMAX, 120" OZ Theatre Majestic 16:9 screen, H/K AVR 7.1...
RUNCO DTV991 LC ( NEC XG 852 LC ) 100" 4:3 screen, H/K AVR 5.1...
|
|
Back to top |
|
|
Curt Palme CRT Tech
Joined: 08 Mar 2006 Posts: 24301 Location: Langley, BC
TV/Projector: All of them!
|
Link Posted: Sun Oct 12, 2014 1:32 am Post subject: |
|
|
Press the little recessed button on the remote, and then press 0,0,0. That will reset the remote address, which is most likely what your problem is.
|
|
Back to top |
|
|
Pellen
Joined: 31 Oct 2013 Posts: 10 Location: Sweden
|
Link Posted: Sun Oct 12, 2014 12:32 pm Post subject: |
|
|
Curt:
Pressing the rescessed button results in osd: projector address 0
Pressing 0 results in Warning Invalid key entry.
And the problem is still there.
Case:
There is no internal remote on this projector. Only a keypad with rubber buttons on the back of the CPU board.
What if I disconnect the IR receiver to se what will happen?
|
|
Back to top |
|
|
CasetheCorvetteman
Joined: 09 Nov 2008 Posts: 6319 Location: Australia
|
Link Posted: Sun Oct 12, 2014 12:35 pm Post subject: |
|
|
Im not familiar with that model so i cant really comment any further
_________________ Barco CineMAX, 120" OZ Theatre Majestic 16:9 screen, H/K AVR 7.1...
RUNCO DTV991 LC ( NEC XG 852 LC ) 100" 4:3 screen, H/K AVR 5.1...
|
|
Back to top |
|
|
Pellen
Joined: 31 Oct 2013 Posts: 10 Location: Sweden
|
Link Posted: Sun Oct 12, 2014 12:40 pm Post subject: |
|
|
Case: Thank you for trying to help
|
|
Back to top |
|
|
barco_75
Joined: 14 Jan 2009 Posts: 169 Location: Chicago
|
Link Posted: Sun Oct 12, 2014 1:34 pm Post subject: |
|
|
I think the problem is that you accidentally pressed the "text" button. The remote is working but when you press this button the screen will not display all of text on the screen. Note sure about why your green tube goes dead. That is a much bigger issue.
|
|
Back to top |
|
|
Pellen
Joined: 31 Oct 2013 Posts: 10 Location: Sweden
|
Link Posted: Sun Oct 12, 2014 4:14 pm Post subject: |
|
|
barco 75:
It happens even with no batteries in the remote.
I think there is a problem with the IR receiver or the CPU board.
Something makes the CPU think there is some wierd input from the remote.
It's possible to turn of one tube using the remote, so I'm not that worried yet.
|
|
Back to top |
|
|
Pellen
Joined: 31 Oct 2013 Posts: 10 Location: Sweden
|
Link Posted: Sun Mar 15, 2015 6:53 pm Post subject: |
|
|
Problem solved (I think).
Disconnected all connectors on the controller, cleaned up behind the rubber buttons and put everything together again.
Now it has been running for hours without problems.
|
|
Back to top |
|
|
|
|