I have a Marquee 8000 that has the H.Fail error code, so I'm looking to buy some boards for it. I need especially an HDM, and probably a CLM, VIM, and a LVPS.
You da man Athanasios! I might incude an F board too. They can cause the dreaded 'powers up OK but no tube output". And they're relatively inexpensive. So much so it doesn't make sense to build a backup parts inventory without one. JMO. _________________ Greg
"Is it ignorance or apathy? Hey, I don't know and I don't care!" --Jimmy Buffett
Joined: 08 Mar 2006 Posts: 3051 Location: Northern Virginia
Link Posted: Wed Oct 22, 2008 3:57 am Post subject: Re: wtb:Marquee 8000 HDM, CLM, VIM, LVPS
johnsmith808 wrote:
Hello,
I have a Marquee 8000 that has the H.Fail error code, so I'm looking to buy some boards for it. I need especially an HDM, and probably a CLM, VIM, and a LVPS.
Joined: 02 Nov 2007 Posts: 211 Location: Rockville, MD
Link Posted: Thu Oct 23, 2008 6:16 am Post subject: Re: wtb:Marquee 8000 HDM, CLM, VIM, LVPS
Clarence wrote:
johnsmith808 wrote:
Hello,
I have a Marquee 8000 that has the H.Fail error code, so I'm looking to buy some boards for it. I need especially an HDM, and probably a CLM, VIM, and a LVPS.
I donated a M8000 VIM to Ralph, but it didn't help his M8111, so he can pass it on to to you.
The only other thing on your list was LVPS, but I donated that to William's stack after a failure at his last meet.
Yes - I still have Clarence's VIM and will send it off to you but you can include something extra for Clarence (that's between you two)
I got my Moome Box back from Taiwain, so after a couple months of no projector its working again, and syncing fine at the moment on both component and HDMI inputs to the Moome box. About 10 days ago I was going to snipe an 81110 parts machine on Ebay - (it went for like $50 and as far as I know worked but had a lot of dust on the lenses http://cgi.ebay.com/ws/eBayISAPI.dll?ViewItem&ssPageName=STRK:MEWAX:IT&item=130260773739 ); but the wife weighed in heavily against (she wants a light bulb). So as per my original plan I am just going to keep trucking and hope my pj stays working. Its got 17000 hours on it and 9 rated tubes so why switch?
Joined: 02 Nov 2007 Posts: 211 Location: Rockville, MD
Link Posted: Thu Oct 23, 2008 6:34 am Post subject: Re: wtb:Marquee 8000 HDM, CLM, VIM, LVPS
johnsmith808 wrote:
Hello,
I have a Marquee 8000 that has the H.Fail error code, so I'm looking to buy some boards for it. I need especially an HDM, and probably a CLM, VIM, and a LVPS.
Thanks!
One thing you may want to try is pushing up the two boards mounted between the CRTs -the one on left was the cause of an H-Fail light I had early on with my 81110. I have the covers taped up tighter now per advice on board (I suppose this is a more likely cause if its ceiling mounted like mine and most others)
Link Posted: Fri Oct 24, 2008 8:35 am Post subject:
I did reseat that as well. I resat all the boards so many times, they must of thought I was playing musical chairs......okay that was lame.
At least I'm getting a good tour of my pj even before I can watch it. Now if something else goes wrong in the future, I"ll have a little bit of experience in troubleshooting.
By the way Ralph, do you have that VIM still that Clarence gave to you? Just in case the problem is in the VIM, it would be nice to have another one to swap out.
Joined: 02 Nov 2007 Posts: 211 Location: Rockville, MD
Link Posted: Fri Oct 24, 2008 4:07 pm Post subject:
johnsmith808 wrote:
By the way Ralph, do you have that VIM still that Clarence gave to you? Just in case the problem is in the VIM, it would be nice to have another one to swap out.
Link Posted: Mon Oct 27, 2008 8:06 am Post subject:
Thanks everyone for helping out. However, my pj took an unexpected turn for the worse when I found out that it is the worse Marquee model ever made. Thus, I will be parting it out instead. No sense putting a lot of time and some money into something that is known to be unreliable.
You cannot post new topics in this forum You cannot reply to topics in this forum You cannot edit your posts in this forum You cannot delete your posts in this forum You cannot vote in polls in this forum You cannot attach files in this forum You can download files in this forum
Forum FAQ
Search
Memberlist
Photo Albums
Register
Profile
Private Messages
Log in
Joined: 12 Jan 2007
Link
I might incude an F board too. They can cause the dreaded 'powers up OK but no tube output". And they're relatively inexpensive. So much so it doesn't make sense to build a backup parts inventory without one. JMO.
